United Security Products AD-2000 Manual de instrucciones descargar pdf (Pagina 11)

Normally Open/I.{ormally

Closed

STEP 6

rne Lco will read:

CHX: N.O./i.{.C.

1(N.O.) 2(N.C.)

A) Press

"1"

select

a normally

open channel.

B) Press

"2"

select

a normally closed

channel.

Momentary/Continuous Activation

STEP 7

rne

Lco

will read:

X: MOIWCONT

I(MOM) 2(CONT)

A) Press

"1"

to select

a momentary

trigger.

B) Press

"2"

to select continuous activation.

Numbers Dialed/Outgoing Messages

Following these steps allows

you

to choose which OGM(s) will

be delivered and

which numbers will

be dialed for each

channel.

NOTE: Dialer LCD

will

only show

programmed

numbers and

OGM options.

STEP 8

rne I-co will read:

CHX:

DIAL#X

1(YES) 2(NO)

("Dial

#X"

being the

number in

phone/pager

location

-8)

A) Press

"l"

dial

phone/pager#X

to be dialed when

the

se-

lected

channel

is activated. Press

"2"

you

not wish

this

number to be dialed.

Continue the above

procedure

for each

the

up to eight

phone/pager

numbers

programmed

in.

STEP 9 ttre LCO will read:

CHX:

OGMX

I(YES) 2(NO)

("OGM

X'being

the OGM recorded

in OGM options #2

#8)

A) Press

"l"

to deliver

OGM

X when

the channel is activated.

Press

"2"

you

not

wish this OGM to

delivered.

B) Continue the above

procedure

for each Channel/OGM. If

you

have

programmed

and

recorded

an ID message as one

your

OGM options, this ID will

be delivered to all channels. It

will

not appear in the

Channel display.

NOTE: ID AND OGM(S)

WILL

ONLY BE DELIVERED TO

TELEPHONE

NUMBERS,

CELLULAR

NUMBERS,

AND

VOICE

PAGERS.

Completing

The

Programming

Once

you

have

programmed

all dialing and OGM options for

each channel, the

LCD will read:

1(YES) 2(NO)

STEP

10 Press

"1"

accept the Channel

programming.

Press

"2"

to re-program or to revert to

previously programmed

setting.

You

are

now ready

review your programming

and test the sys-

tem.

PRESS

"M''

TO EXIT PROGRAMMING MODE.

Test

your

system before an emergenc! occurs.

Do not neglect to review

programmed

information and

verify

all

elements of

your

system thoroughly before

relying

on the dialer

to deliver the

necessary infbrmation

to the desired

parties

accu-

rately and completely.

strongly recommend testing the

system

test

mode

before

connecting

to a telephone line. The test mode tests the stored

information, not the full tunctionality

the

dialer.

test

the

full functionality of the dialer, the unit must be tested in the op-

erate mode.

the test

mode.

the dialer

will not

make more than

one attempt

per

number

dialed

play

any

OGM

more than

once.

NOTE:

IF YOU ENTER THE WRONG

CHOICE.

PRESS

"M"

KEY

REPEATEDLY AND

RETURN TO THE'PROGRAM MODE'" THEN

SELECT

THE SECTION TO CHANGE

('T"

ACCEPT SECTION,

"2''

FOR NEXT SECTION). THEN ENTER CORRECT INFORMATION.

STEP

I Press the

"M"

Mode key

until

the LCD reads:

TEST: T-LINE

rffES) 2(NO)

STEP

2 Press

to display the

T-Line

configuration.

The

data

will scroll

through all

selections.

Press

"2"

to scroll

the next

section.

STEP 3

tne

LCo

will read:

TEST:

CHANNEL(S)

1(YES) 2(NO)

Press

"l"

test

channels.

Press

"2"

to scroll to the next

section.

STEP 4 ttre LCO will read:

SELECT:

1-4

5(ALL) O(DONE)

Select the channel

you wish

to test

(

-4).

Press

"5"

to test

"all"

Channels. Once a channel is selected

(or

"all")

the

programmed

channel information will

displayed

on the

LCD. Verify

data

accuracy as the LCD scrolls through

comparing the information

displayed

with

that specified on

your

Program Planner. Listen

your

recorded message(s) to ensure that the correct OGM

(if

pro-

grammed)

is delivered. Press

"0"

to exit testing.

STEP 5

Now

connect

your

dialer to the telephone

line you will

be using and test the system again, to determine if it functions

correctly in an actual emergency situation.

Make

sure

you

notify

the

receiving

party

your

intent to call them,

and tell them it is

iust

a test.

STEP 6

test the operation of

your

entire system, set

Mode

OPERATE

and

proceed

as explained

the

next section:

Operat-

ing Your System.

Test

your

system on a regular basis, at least once a week.

1 2 ... 6 7 8 9 10 11 12 13 14 15 16

Comentarios a estos manuales

Sin comentarios

United Security Products AD-2000 Manual de instrucciones Pagina 11

Comentarios a estos manuales

Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad United Security Products AD-2000